Where to Put Stamp on Postcard With Barcode?

Where to Put Stamp on Postcard With Barcode?

Where to Put Stamp on Postcard With Barcode?

The stamp is placed in the upper right corner of large postcards, which are normally 8.5 inches by 11 inches in size, exactly above the address and barcode. Inquire with the postal office about postage costs or any other issues related to mailing.

Postcards have special stamping requirements. You must put your stamp in the upper right corner of the postcard on the same side as the address. This helps sorting machines orient the mail and aids in OCR-reading of the address. In addition, a neat stamp will speed processing time. Postcards are processed as First Class mail but at the Priority Mail speed.

Address area

When you want to post a postcard with a barcode, you will need to know where to put the postage stamp. It would help if you placed the stamp in the top right corner, above the barcode, and the return address in the bottom right corner. Some postcards have a rectangle to indicate where to put the stamp. Using this space correctly will make the postcard more likely to be delivered on time.

When you print the barcode, you should place it about 5/8ths of an inch from the bottom of the postcard. If you don’t want the barcode to cover the entire postcard, you can place a sticker over this area. It would help if you also remembered to leave room for the message area and the right portion of the postcard. It would help if you also were sure to include the postage and any United States Postal Service markings.

Where to Put Stamp on Postcard With Barcode?


You should also follow USPS guidelines for where to put a postcard with a barcode. The barcode needs to be about 4 inches away from the bottom edge of the mailpiece. However, it should not overlap with the address block line. This area is called the “safe area.” If it’s too close, the postcard will get trimmed. You should also make sure to give the barcode enough space on the postcard so it will be easier to scan by the postal machines. This will ensure that the postal workers can read your postcard and address.

See also  Never Trust a Cecil | The Origin & Meaning

Postcards vary in size from 3.5×5 inches to 8.5×11 inches. The address area should be at least 1.5 inches high and extend up to 1/8 of an inch above the bottom edge of the card. You may also want to include your return address at a lower location, approximately five-eighths of an inch from the bottom.

The barcode on a postcard is not always correct. The date on the barcode is usually the date selected by the sender when the postcard was printed. This date is not always accurate, and the USPS requires accurate date imprinting when using a PC postage product or mailroom meter. It would help if you stamped the postcard with an accurate date, or the postcard will not be mailed correctly.

The stamp should be placed in the upper right corner of the postcard, above the address. Afterward, the postcard can be dropped off in a mailbox, USPS mail dropbox, or at a post office counter. Postcards are handled similarly to First Class mail, though they are handled more quickly.

Barcode area

The barcode area on a postcard is an essential part of the postcard’s design. Postcards without a barcode area will require additional postage, often taking longer to deliver. It’s important to remember that the area must be at least four and a half inches wide by five and a half inches high, without any other print.

Where to Put Stamp on Postcard With Barcode?

There are certain areas of a postcard that must be white. These areas include the address area, the barcode area, and the postage area. This area is typically 1.625″ by 1.375″ and is located on the back side of the postcard. The address area, the bar code area, and the bleed area must all fall within a 0.25″ margin of the postcard’s trim line.

Regardless of how you design the barcode area, it’s vital to include it where it can be read easily. The Post Office recommends putting it about five-eighths of an inch from the bottom of the postcard. You can also include a sticker over the barcode area if necessary.

See also  How to Address a Postcard Without Lines?

The barcode area on a postcard is a small, rectangular area located on the right-hand side of the address side. This area must be clear enough to read the barcode. In addition, this area must have a minimum of four digits for it to be read correctly. Finally, the barcode area must also contain the entire barcode.

The carrier release endorsement must appear above the return address area if the card is being sent via mail. Alternatively, the carrier release endorsement must be directly below the return address. It must be separated from the address block by at least one blank line of type size. This area’s read direction must match the delivery address’s read direction.

Another type of barcode on postcards is the Facing Identification Mark. This is an identifier designed by the United States Postal Service. This barcode is usually a series of vertical bars positioned near the postcard’s top edge. It’s also found near the postage area on an envelope. The Facing Identification Mark is required on pieces using the BRM mailpiece standard and computerized cancellation equipment.

Postcards with a barcode on them may contain a UPC or EAN code. This type of barcode has a two-digit supplement ranging from 00 to 99. Some software systems can use this type of barcode to track stock. A postcard with a UPC barcode is a relatively low-cost option.

Return address area

When printing postcards with barcodes, it is essential to remember the size of the return address area. It should be approximately three-eighths of an inch tall and approximately four-tenths wide. If the address is smaller, the addressing area should be approximately three-fourths of an inch tall.

It is also important to remember that the barcode area must be broad enough to accommodate the barcode. Depending on the printer and software used, this space can be as large as three and a half inches. If the barcode requires an extra-wide space, it must be sprayed onto the envelope.

See also  How to Fix a Leaky Bathtub Faucet Without Turning off the Water?

Intelligent Mail barcodes should be placed, so they do not overlap the address label. To do so, you must ensure that the barcode is at least 0.028 inches from the edge of the address label. If the barcode covers the address block, it will be positioned near the right-side corner of the postcard.

It is important to note that the carrier release endorsement must be located above the delivery address area. In addition, the unit designator should appear directly below the return address. This area is critical to mailers who want to ensure that their postcards are delivered correctly. If a postcard is delivered incorrectly, it can be returned to the sender, which is a costly mistake.

Postcards are available in different sizes and shapes. A postcard six by four inches in size is considered First Class mail, while those smaller than that will be classified as budget mail. When printing postcards, ensure that the address area is free of UV or aqueous coatings. Otherwise, laser addressing will not be possible. You can also ensure that the barcode area is free of background graphics.

Another essential detail of a postcard is its design. The postcard should be in an area where the barcode is clear, making it more visible and more likely to arrive at the recipient’s door on time. In addition, having a clear barcode on a postcard can make it look more professional.

In addition, the return address area on a postcard must be located above the main panel. It is included with First Class Mail but is optional for standard mail. You must also adhere to USPS requirements when designing postcards, such as dimensional and format. You must have a left and right message area and the address and postage.